Plumbing Basics: A Must for Installing a Bathtub
Plumbing Basics: A Must for Installing a Bathtub
Blog Article
Are you currently looking for information concerning Installing A Bathtub?
Mounting a bathtub isn't exactly rocket science, however it does require strong plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old bathtub with a new one is also a moderately hard project. If the old bathtub is easily easily accessible, the project can relocate easily; if you need to open up a wall to eliminate the old tub and also place the brand-new tub, the job is much harder. In either instance, the job is within a house handyman's skills, although you will need an assistant to leave the old tub and embeded in the brand-new one. See to it you have qualified on your own for the job and also are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed project, it is better to think about utilizing one before you begin. Opportunities are you may require a specialist plumber to make tube connections.
This post will help you mount a new bath tub in your restroom if you have actually already bought a new tub and do not require to transform the plan of your previous water pipelines.
Your tools as well as product checklist need to make up the following:
Getting ready for the Installment
Firstly, the sustaining frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets unit to prevent pressure on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you make use of every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be fitted in its last placement.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be quite bothersome due to the restricted access that is commonly the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric ready for the staying water that will certainly come from the pipes. Once the supply pipes have been removed, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
Before moving on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Making use of both wooden boards under its feet, put the bath tub in the called for placement. The wooden boards are practical in evenly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 tiny factors.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub till the spirit level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable tap adapter to the proper supply pipeline by making a compression join; after that do the same for the other tap.
Activate the water system and also inspect all joints and also brand-new pipework for leaks as well as tighten them if necessary. Fill the tub and additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the maker's instruction manual. Tiling and securing around the bathtub must wait till the bath tub has actually been used a minimum of when as this will settle it into its final position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end gives a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washing machines are in place between the tap as well as the sink. Secure the tap in place with the producer offered backnut. When the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical tap connectors. The previous kind ought to be linked to the tap finishes first, tightening up only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to break a stiff seal, causing the water to penetrate the wall surface in between the bath and the tiling, bring about complications with dampness and also possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures and also installations. They are sold in tubes and also cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the motion experienced when the tub remains in use. The sealer can fracture rather early if you do not consider this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently offered on the marketplace. It is advisable to fit the tiles utilizing water-resistant or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when exploring the internet. If you enjoyed our article kindly don't forget to pass it around. I am grateful for your time. Please check up our blog back soon.
24/7 emergency? We're here! Report this page